- Nextengine scanstudio hd link how to#
- Nextengine scanstudio hd link manual#
- Nextengine scanstudio hd link software#
So, back to the drawing board (or Imaging Lab, haha) and we’ll see how the adjustments work out.Soil structure is an important physical property that can be degraded by soil tillage, but methods for quantifying soil structure are both few and time consuming. As a group, we are searching for additional documentation (found a good one put up by the folks at Ball State University) but any other input is welcomed.
Nextengine scanstudio hd link manual#
I’m a big advocate of learning by doing, but I must admit to being a little frustrated at the available documentation for the scanner like many other technical documents, I feel as if the training manual isn’t necessarily written in accessible, plain language.
Nextengine scanstudio hd link software#
Scanning larger objects creates too much data for the software and system to process.” I then asked if the item being scanned was smaller (in comparison to this baseball), would I be able to use the 2nd or 3rd click on HD the response was: “The highest HD modes are for small objects with very fine detail.
Nextengine scanstudio hd link how to#
For more information on learning how to scan, please download and view our webinar demo ” Also, try fusing with 0.0000″ for the simplify slider. Try scanning in SD on 3rd click, or HD on 1st click. The first question they had for me was “What is the point count for the entire model, and what is the resolution ratio that you are using?” (Answer: 10,392,197 points, and the 3rd click on HD) The response back from tech support reads as follows: “We recommend a maximum size of around 6 million points. I closed the program, restarted, and attempted to fuse the images a second time but received the same error message at the same point in the process.Īt this point, I sent a message to the tech support folks outlining this issue and asked for their input. More on this as I learn more.) The fusing process proceeded until roughly 75% completion, at which point I received an error message that said “NextEngine ScanStudio File has stopped working”. (*this is all purely speculation…I haven’t been able to find out much information about this step that is written in a way I understand. Admittedly, I am unsure exactly how this slider affects the fused result, but by moving it downward that amount turned the indicator bar from yellow to green, which seems to indicate a positive action. This is where today’s issue occurred the simplify tolerance slider indicated a number near 0.06xx”, and I moved it downward to 0.0500″. After aligning these two scans (which also was a challenge, as finding distinguishing marks on a sphere is VERY difficult, and because it is a museum object there was no way to add temporary markings for alignment), I determined that no further scans were needed, as all areas were well covered and there were no apparent data holes.Īfter aligning and trimming the excess data (scan arm, etc.), my next step was to fuse the images. The two scans were completed using the 3rd click (highest) HD setting, shading neutral, and each scan took about 27 minutes to complete. I did two, 360* scans of the baseball, rotating it 90* forward in a straight line to capture the areas at the top and bottom that were missed on the first scan (the image from the first scan looks a little like a donut, with what basically amounts to a hole through the center of the baseball). It’s a standard baseball, with a lot of wear…in one area the leather is completely torn away, revealing the string wrapping underneath. The first object I am scanning for our collection is a 1908 baseball used in a University of South Carolina vs. That being said, appropriately enough I have an issue from today that is prompting this inaugural post. Our hope is that by documenting our own successes and challenges, we can begin to create a body of information and work-arounds for issues we encounter, as well as solicit help from others. We’ve started this blog as a way to document not only the learning curve of the new group of assistants and interns in the SLIS 3D Imaging Lab, but to create a web presence and develop relationships with other institutions using the NextEngine 3D Desktop Scanner.